The kit includes enough rings for 3 pairs and lots of leftovers.

The kit includes enough rings for 2 pairs + nearly 200 leftover rings—make a bracelet to match!

The kit includes enough rings for 1 pair.

The kit includes enough rings for 1 pair.

The kit includes enough rings 3 pairs + lots of leftovers.

The kit includes enough rings for 1 pair.

Note: This kit includes enough rings to make either the longer Intricate Crescent (2nd photo at top right in the book) or the shorter version (3rd photo). If you make the shorter version, you will have about 20 rings left over.

The kit includes enough rings for 3 pairs + lots of leftover rings.

The kit includes enough rings for 3 pairs + lots of leftover rings.

Tip: This kit includes headpins that are exactly the right length. Snip off the "head" of the headpin with wire cutters, and then make your loops following the steps on pg 30-31. Your loops should be about a "C" size inner diameter (7/64" / 2.8 mm). It might take a couple of tries to get the loops just right, and that's why we include some extra headpins in the kit!

The kit includes enough rings for 3 pairs + lots of leftover rings.

The kit includes enough rings for 1 pair.

The kit includes enough rings for 1 pair.

The kit includes enough rings for 2 pendants + lots of leftovers.

The kit includes enough rings for 1 bracelet + lots of H18s leftover.

The kit includes enough rings for 1 pair + some B20 NIOB leftover.

The kit “as is” has enough for 2 rings.

Notes: For the titanium rings, this kit contains size C22 (22ga 7/64" / 2.8 mm), as these are a better fit than the B22 size listed in the book.

The kit includes enough rings for 1 bracelet + a little leftover.

Note: The colors listed are lime and midnight blue, but in the photograph in the book, they look more like emerald and plum. (Niobium is tricky to photograph!) The kit includes lime and midnight blue rings, so expect the green to be brighter/more yellow and the blue to be less plum.

These kits are all customizable!

Please view them in the the customizable kits section..

Want to customize your project with different colors or clasps? Simply purchase rings à la carte on our ring picker page
and other components on our Clasps/Findings/Specialty Beads page.

Errata: The number of J17 rings listed in the book is incorrect. The correct number should be 116.

Additionally, the instructions don't say what the soldered ring is for. It is intended to be used on the side of the necklace opposite the clasp, to be a sturdy ring that the clasp can hook onto. All kits include a solid ring of approximately 15 gauge.

The kit includes enough rings for 2 pairs.

Ripple Earrings uses different ring sizes than Ripple Necklace. Kit comes with a weave diagram that details where to use each size within the weave to create the earrings.

The kit includes enough rings for 2 pairs.

Ripple Earrings uses different ring sizes than Ripple Necklace. Kit comes with a weave diagram that details where to use each size within the weave to create the earrings.

The kit includes enough rings for 2 pairs.

Ripple Earrings uses different ring sizes than Ripple Necklace. Kit comes with a weave diagram that details where to use each size within the weave to create the earrings.

The kit includes enough rings for 1 pair.

Ripple Earrings uses different ring sizes than Ripple Necklace. Kit comes with a weave diagram that details where to use each size within the weave to create the earrings.

Tip: This kit includes headpins that are exactly the right length. Snip off the "head" of the headpin with wire cutters, and then make your loops following the steps on pg 30-31. Your loops should be about a "C" size inner diameter (7/64" / 2.8 mm). It might take a couple of tries to get the loops just right, and that's why we include some extra headpins in the kit!

Want to customize your project with different colors or clasps? Simply purchase rings à la carte on our ring picker page
and other components on our Clasps/Findings/Specialty Beads page.

New to Maille? The kit as shown in the book uses stainless steel and bronze jump rings. These metals are VERY difficult to work with (especially the stainless steel) so we recommend choosing one of the other kit combinations below if you have never worked with stainless steel before and/or are new to chainmaille.

Note: We currently sell aluminum and jewelry brass versions of this bracelet.

Errata: The clasp for the sterling bracelet is different from the aluminum bracelet (shown in the step by step photos). In order to properly connect to the sterling clasp, you may need to adjust the way you finish, as shown in this diagram. All sterling kits include D18 and B19 rings should you wish to finish this way.

Want to customize your project with different colors or clasps? Simply purchase rings à la carte on our ring picker page
and other components on our Clasps/Findings/Specialty Beads page.

Note: For the titanium rings, this kit contains size C22 (22ga 7/64" / 2.8 mm), as these are a better fit than the B22 size listed in the book.

Note: If you purchase rings à la carte for a Sterling Silver and Niobium version, know that the weave is much more supple in those metals. Very, very flexible.

Note: This pendant is larger than the mini silver pendant shown on the model. Pendant measures 2.125" (5.39 cm) not including bail.

These kits are all customizable!

Please view them in the the customizable kits section..

Want to customize your project with different colors or clasps? Simply purchase rings à la carte on our ring picker page
and other components on our Clasps/Findings/Specialty Beads page.